Part No. 0970
Key Joint Box 2

For replacing and removing joint box covers (with the exception of 21 & 22). This key is also perfectly suitable for use on Frame & Cover Unit Light and Frames & Covers Carriage Way 4. One side of the handle is chisel shaped for cleaning out cover key holes and the frame channels.
Part No. 0975
Key Joint Box 3

For removing the covers of joint boxes 21 & 22 only. This is a "T" handled tool made of hardened steel. Note: due to it's design and light construction this key should not be used for any other type of cover.
Part No. 0971
Key Joint Box 4

A long handled version of Key Join Box 2, enables the cover to be lifted in the standing position and can also provide extra leverage for covers which are difficult to remove. For replacing and removing joint box covers with the exception of 21 & 22. This key is also perfectly suitable for use on Frame & Cover Unit Light and Frames & Covers Carriage Way 4.

2.4 kg, 500mm Handle Length
Part No. 2367
Key Joint Box 5

This item is used for removing and replacing of foot way and driveway covers and also used for safe gas testing of joint boxes prior to removal of covers. The unit is designed to enable the user to lift in a safe standing position away from the edge of the box.

Approx weight 2.5 Kg.
Part No. 0972
Key Lifting Carriageway 2A (D Key)

A steel tool for lifting E type and unit type covers of rectangular and square shape. The key is locked to the cover by an adjustable locking nut, then a jacking bolt is turned which bears against the frame to lift the cover. The yellow colour is to differentiate this metric version of the tool from the earlier Imperial Key Lifting Carriageway.
Part No. 0973
Key Lifting Manhole Cover (T Key)

A tool for lifting circular, oval, "Woods" type and triangular carriageway covers. This key is made of steel and an eye is incorporated so that a crowbar can be used to assist in lifting.
Part No. 0974
Key Pillar

For opening Cabinets Cross Connect, Pillars Distribution, Posts Jointing and hollow pole doors. This is a small "T" handled tool.
Part No. 0036

Manhole Cover Lifter

Used for lifting of all types of carriageway covers. Requires much less effort than lifting covers manually. Includes a handle for operating the hydraulic ram and another for manoeuvering the lifter. It can develop a 1.5 ton breakout force to move even the most awkward manhole cover. Can be simply assembled in under 30 seconds and requires neither skill or strength.

The lifter is mounted on three nylon wheels providing good stability during lifting and mobility whilst the cover is in the raised position. Lifting is acheived by means of a hydraulic ram, this is operated by a pumping action, lowering is acheived by a key-release valve. For moving over rough ground, a handle for lifting is provided.

All keys ordered seperately.

Keys and Accesories

Universal Seal Breaker

Swivel Ring Locker Spreader
(Both the above used when 2 pairs of keys are needed)

Elkington Keys

Key Type 1 and 5
(Only used when manhole has only two holes)

Spare Parts

Nylon Wheel

Hook

Pumping Handle

Pulling Handle



Z-5635

Z-5636



Z-5637

Z-5637





Z-5090

Z-5638

Z-5078

Z-5089
Rope Cabling

Pre-stretched terylene rope for use by Rodding and Light cabling parties only. Supplied with a spliced eye at each end on wooden reels.
Rope Cabling 1 has a breaking strength of 2400 Kg. Rope Cabling 4 is double coated for very low friction and has a maximum breaking strength of 6000 Kg.

Other reel lengths are available on request.

Ordering
Rope Cabling 1
Rope Cabling 4
Rope Cabling 4
Length (m)
250
200
500
Code
0920
0922
0923
Part No. 1073
Draw Rope

Used for pulling small cables and heavier cabling ropes into duct. Three strand polypropylene rope.

Max load 550 Kg.

500m x 6mm
Brush Cylindrical

Used for the cleaning out of empty duct bores. This is a range of brushes designed to suit the various sizes of ducts available. All brushes have an overall length of 350 mm.



Br. Cyl. 57mm
Br. Cyl. 80mm
Br. Cyl. 86mm
Br. Cyl. 95mm

Br. Cyl. 108mm

Dia. Used with duct
51 mm bore
76 mm bore
83 mm bore
90-92 mm bore
102 mm bore



0525
0526
0527
0528

0524
Mandrel Iron

A metal cylinder with a pulling eye at each end. All mandrels are colour coded for ease of identification. They are all 240mm long except for type "43" which is only 200 mm long.



M. Iron 43
(Unpainted)
M. Iron 70
(Red)
M. Iron 76
(Grey)
M. Iron 79
(Black )
M. Iron 83
(Yellow)
M. Iron 95
(Green)

Used for duct with
51 mm bore

76 mm bore

83 mm bore

92 mm bore

90 mm bore

102 mm bore



0343

0344

0345

0346

0347

0348
Cobra (Continuous Rods)

Continuous high quality coated fibreglass rod with brass end fittings and smooth profile guiding tip. This type of rodding is faster and more economical than the screw together type rods. The frame is of a rugged steel construction with zinc plating and an integral fully adjustable brake system fitted as standard. All frame and rod fittings are available as spares.

Other lengths than those listed are available.

Cobra 6.7 mm x 120 metre
Cobra 9 mm x 80 metre
Cobra 9 mm x 120 metre
Cobra 9 mm x 150 metre
Cobra 11 mm x 150 metre
Cobra 11 mm x 200 metre
Cobra 11 mm x 250 metre

0498
0493
0492
0497
0496
0495
0494
Rods Duct (Yellow Duct Rods)

PVC rod with male coupling one end and a female one at the other end. Used for general purpose rodding where machine rodding is impractical. Integral latching type couplings to prevent the rods becoming disconnected in the duct.

Rod duct 1&2 - 24 mm outside dia.
Rod duct 5 - 13mm outside dia.

Ordering
R. D. 1 Ferret
R. D. 2 Ferret
R. D. 5 Ferret

Length
3 Metres
2 Metres
2 Metres


0402
0403
0405
Part No. 0414
Coupling Rod Duct 3 Female

Used in conjunction with Coupling Rod Duct 3 Male Swivel, to make a leader rod out of Rod Duct 1 or 2. Provides a female thread at the trailing end of the Leader Rod for connection to Rod Duct 3. Also used in conjunction with Coupling Rod Duct 3 Male Swivel to repair Rod Duct 3.
 
Part No. 0436
Attachment Rod 2A

Combined leader and follower for attaching to the male end of Rod Duct 5.
 
Coupling-up Piece

Two interlocking fittings used to marry Rod Duct 1 or 2 to Rod Duct 3 or a Ductmotor. Coupling piece 2 is of larger diameter and can be used where there is more space in the duct.

Coupling-up Piece 1-ferret
Coupling-up Piece 2-ferret

2092
2093
 
Adaptor Rods

Adaptor Rod 1A
Allows Rod Duct 1 or 2 to be connected to Rod Duct 3 thereby facilitating machine rodding in excess of the maximum Rod Duct 3 length of 250m.

Adaptor Rod 2A
Allows for the attachment of Oscillator 154B. Attachment Rod 4A or Coupling-up piece 1 or 2 to the male end of Rod Duct 1 or 2.

Adaptor Rod 3A
Allows attachment Rod 4A to be attached to the female threaded end of Rod Duct 1 or 2.

Adaptor Rod 7
Allows Rod Duct 5 to be attached to Rod Duct 1 or 2.
Adaptor Rod 1A
Adaptor Rod 2A (Part of Leader/Follower)
Adaptor Rod 3A
Adaptor Rod 7
0370
0371

0372
0376
 
Link Cabling

Link Cabling 1 - Used to attach cable grips to Rope Cabling 1.

Link Cabling 2 - Galvanised mild steel link of 10mm diameter, used for attaching cabling ropes to cable grips. For use on large cables.

Link Cabling 1
Link Cabling 2

0338
0339
 
Part No. 0340
Link Keystone 1/2

A chain link in the form of a figure eight, made of high tensile steel. Has two pivoted halves which give a quick release facility. Used to connect Cable Grips, Brush Cylindrical and Mandrel Iron to cabling ropes.
   
Connector Swivels

22mm 2A - For installing Optical Fibre cable with a central strength member in duct or sub-duct. This is a fused swivel connector used in conjunction with Connector SCM 2A. The fuse supplied has a breaking strength of 4kN, but replacements of various breaking strengths are available.
Connector Swivel 1 - Used to attach Grips Cable Single Eye to rope Cabling 4. Two swivelling forks with removable clevis pins for attaching the rope and grip.

Connector Swivel 2A-22mm
Connector Swivel 1

0780
0935
 
Grip Cable Fleeting Single Eye

Grip Cable Single Eye Closed
Wire mesh tube for use in drawing in and recovery of cable. The tube reduces in diameter and grips the cable tightly as tension is applied to the pulling eye.


Ordering
13 mm
19 mm
25 mm
38 mm
51 mm
63 mm


Cable Dia.
13-19mm
19-25mm
25-38mm
38-51mm
51-63mm
63-76mm


0324
0325
0326
0327
0328
0329
 
Grip Cable Fleeting Double Eye Open

Wire mesh tube for use in drawing in and recovery of cable. The tube reduces in diameter and grips the cable tightly as tension is applied to the two pulling eyes. The tube is open at both ends and it may be slid along the cable and repositioned during the cabling process.

Ordering
25 mm
38 mm
51 mm
63 mm
Cable Dia.
25-38mm
38-51mm
51-63mm
63-76mm


0316
0317
0318
0319
 
Part No. 0223
Pump Lubricant 2A

For applying Lubricant Cable 2A to sub-duct or cable during installation. Comprises a hand operated pump mounted on a plate which is designed to be fitted directly on top of the lubricant container.
 
Part No. 0236
Lubricant Cable 2A

Used during the installation of cables into underground ducts, reduces friction between the cable being installed, duct walls and existing cables. Container 20 litre.
 
Part No. 0563
Reel Hose 6

Portable Hose Reel, mounted on a wheeled trolley with a winding handle. Comes complete with Hose Pneumatic 3. Used to operate duct motors in conjunction with rodding and light cabling vehicle and air compressor sets.
 
Part No. 0211
Duct Motor 2B

For pulling drawrope and light cable into ducts.
 
Bag Grips

Bag Grip 4
Universal size for use with Duct Motor 2B

Bag Grip 5
Small for use in congested ducts on Duct Motor 2B.

Bag Grip 4 (medium)
Bag Grip 5 (small)

7023
7024
 
Guide Cabling

For use in 90mm internal diameter duct during cable installation.

Guide Cabling 1 - is ideal for use where these is no significant angular deviation between the duct route and the cable leaving the duct mouth. Also used for cabling through jointing chambers where duct tracks are in line.

Guide Cabling 2 - is ideal for use where there is an angular deviation of less than 30 degrees between the duct route and the cable entering or leaving the duct mouth. Also used for cabling through jointing chambers where duct tracks are not in line.

Guide Cabling 1
Guide Cabling 2

0900
0901
 
Part No. 0226
Roller Rope Guiding Surface

For guiding drawropes and cabling ropes out of joint boxes and manholes, to avoid damage to the rope on the box edge. This consists of a metal roller mounted on a frame which locates on the edge of the box by means of two lugs.

10" long x 6" wide.
 
Bellmouth Split

Bellmouth Split 1 and 2
Used to prevent damage to the cable against the abraisive edge of the duct mouth during installation of the cable. Consists of a split tubular sleeve that is assembled over the cable and is held together by two wing nuts, it fits loosely into the entry duct mouth. For use where the angular deviation between the duct route and the cable entering the duct is not significant.

Bell. Split 1

Bell. Split 2

83mm int dia duct
90mm int dia duct

0928

0929
 
Part No. 0588
Gun Applicator Resin Pack 14

Used to apply the resin from resin pack 14.
 
Part No. 1180
Resin Pack 14 A

For sealing duct entry points in all cabinets cross connection.
 
Part No. 1180

Stools Folding

Generally used by external cable jointers, but suitable for any situation where a lightweight folding stool is required. Consists of a tubular steel frame with a canvas seat.

14" x 8" x 15 1/4" high
 
Part No. 0736
Circumfrential Cutter

An adjustable tubing cutter with diecast body. With a hardened steel blade and two flare groove rollers. The adjusting knob also incorporates a retractable reamer and spare cutting wheel.

Capacity 6 - 38 mm
 
Part No. 0600
Sheet Canvas 5'9" x 5'

For protection of cables during jointing, made of lightweight green coloured canvas which does not drip when wet. For securing purposes there is a metal eyelet in each corner and one in the middle of each side.

14oz/sqyd 5'9" x 5'
 
Sheet Waterproof

A general purpose waterproof sheet. For securing purposes eight metal eyelets are fitted around the perimeter of the sheet.

Sheet Waterproof 1 is made of rubberised cotton fabric, light grey in colour. 5' x 4'2"

Sheet Waterproof 2 is made of medium weight khaki green canvas.
22 oz/sqyd, 6'6" x 6'6"

Sheet Waterproof 1
Sheet Waterproof 2

0601
0602
 
Part No. 0603
Sheet Rubber Self Adhesive

Designed to provide a temporary watertight closure for underground cables. Saves closing a joint up completely at the end of every day. Suitable both for grease filled and pressurised cable.

8yds x 27"
 
Part No. Z-5488
Pop-Up Tent

This A series pop-up tent comprises of light frame components and a sginle slit door. There are lie down cords throught the hub on three sides and ground flaps for weight anchoring.
Other features include the rubber non-slip feet and a carrying case with steel tent stakes.
Comes in standard yellow and white colours.
 
Part No. Z-5489
Collapsible Workman's Tent

The tent cover is made of flame resistant polyester reinforced PVC, white in colour. The flame resistant complies with BS 5867 Pt.2. The frame is constructed of aluminium tubing and stainless steel. The cover is permanently attached to the frame, providing quick and easy assembly.
 
Frame and Cover Footway

Provided in various sizes to suit different joint boxes or chambers. All covers are available either concrete filled or unfilled and with or without a logo.
Type and weight

Footway 2 - 43Kg
Footway 4 - 80Kg
Footway 5 - 73Kg
Footway 6 - 143Kg
Footway 10 - 295Kg
Footway 11 - 217Kg
Clear Opening (mm)
725x256

455x915

612x612

613x1310

742x2319

710x1690
Code


2071

1001

1002

1003

1004

1005
 
Frame and Cover Carriageway

For use on carriageways and anywhere with fast moving or heavy traffic.

Type 1 has 2 lids and has a clear opening of 605x605.
Type 2 has 4 lids and has a clear opening of 600x1200.
Type 3 has 6 lids and has a clear opening of 675x1800.

The number in brackets after the type below is the frame depth.

Type and weight

1 (150) - 140Kg
1 (100) - 104Kg
2 (150) - 412Kg
2 (100) - 304Kg
3 (150) - 565Kg


Code

1012
1015
1016
1013
1014
 
Box Joints

Mostly used on housing estates to hold Sleeve 31A, made of prefabricated glass reinforced polyester. Other sizes of pre-formed jointing chambers are available.

Box Joint 23
Box Joint 26
Size (mm)
200x450x450
720x250x570
  

1017
1018
 
Part No. 1019
Cover Box Joint 23

Cast Iron lid for use on Joint Box 23.
 
Step Manhole

Access Step for use in concrete and brick manholes. Step Manhole 1 built into the wall during construction.

Step Manhole 1
Bolt on Step Iron
(two holed)

1035
2460
 
Part No. 1042
Bolt Expansion 1A

Used for fixing of Bolt On Step Iron and cable bearers in existing underground structures.

1/2" x 2 3/4"
 
Part No. 0306
Ladder Manhole Steel

For providing access into manholes. Comprises of a ladder, mounting bar and two wallmounted hooks, all made of galvanised mild steel. Designed to be fitted during the construction of the manhole.

Length - 2300 mm
 
Part No. 1038
Iron Anchor 4

Used for holding cable guides etc. by means of the appropriate chains, ropes and shackles. For use in jointing chamber walls and ceilings, it is embedded in the wall leaving a loop sticking out of the wall.

Type of wall: Concrete
Loop extending from wall: 76mm
   
Part No. 1044
Bolt Foundation Indented 2

Generally used for the fixing of Cable Bearers in new concrete and brickwork. 5" x 1/2"
 
Part No. 1065
Grating Sump 2A

Used to allow for water drainage in manholes and joint boxes. Made of PVC and square in shape.
250mm x 250mm.
 
Duct Repair Kit

Used in the repair of damaged Duct.
Comprises 4 Duct Split inserts, 6 Duct Liners and 8 Strap Cable Fixing 10A. Kit 2A needs Split Duct 59A and should be used on Duct type 11. Kit 3A needs Split Duct 54D and should be used on Duct type 54, 54D and 55.



Kit 2A
Kit 3A

Duct Size (mm)
73-80
88-98
 

Code

1716
1717
 
Part No. 1703
Duct 70

Heavy duty steel ducting

11.3kg/m. 6.375 x 102mm diameter. Minimum order quantity 51m.
 

Duct Split

Used in the repair of damaged sections of Duct this is made of thick walled rigid PVC with each length comprising two halves. In 3 metre lengths.

Type 56 used on Duct 56 (49mm), Type 59A used on Duct 11 (73-80mm), and Type 54D used on Duct 54D, 54, and 55 (88-95mm).

Type

56

59A

54D

Also required
Strap Cable Fixing 10A
Duct Repair Kit 2A
Duct Repair Kit 3A
  

Code

1704

1707

1708
 
Part No. 1738
Gland Caulking 2

Used in the sealing of Duct 54.
 
Connector Bend

Used in the sealing of Duct 54.

Connector Bend 1 used for the connection of a duct to Capping Steel.
Connector Bend 4 used mainly on new housing developments to connect Duct 102 or 56 to Cover 101A and Capping 25.

Connector Bend 1
Connector Bend 4

1167
1168
 
Part No. 1720
Collar Duct 54A

Used in the joining together of mole ploughed lengths of Duct 54.
 
Part No. 1713
Duct Tee 54/56

Used on housing estates for providing the lead into customer premises. Made of PVC and used with Duct 54D with a tee to connect to Duct 56.
 
Bend Duct

Used when the route of the duct requires a turn. Made of PVC, the name relates to the type of duct the bend connects to, i.e. Bend Duct 54B Duct 54. All angles are 90 degrees apart from Bend Duct 54B which is 18 degrees.

Bend Duct

54A
54B
56
56A

Radius Bend (mm)
457
3000
350
622
  

Code

1723
1724
1725
1726
 
Plug Duct

Plug Duct 1A used to seal Duct 54D whilst laying it. Colour coded for ease of identification. 4B is red, 4C is yellow.


Plug Duct 4B
Plug Duct 4C

End of used
Socket
Spigot
  

Code
1287
1288
 
Disc Caulking

Used in sealing duct ends. The discs are used in pairs, fitted in a duct gland and sealing compund compressed in between the two discs to form a seal which is proof against water and gas. All discs are 6mm thick.

Types 1 & 2 are commonly used on Duct 54D and Type 4 is commonly used on Duct 56.

Disc.C
1
2
4

Dia. (mm)
92
96
55
  

Code
1734
1735
1737
 
Duct

A standard light grey plastic ducting with a vicat softening point of 75 degrees. Duct 56 is 3M in length, Duct 54D is 6M in length.


Duct 56
Duct 54D

O/S Dia.
53.8-54mm
96.3-96.7mm
  

Code
1702
1701
 
Part No. 1173
Resin Bedding

Used as a bedding for Frames and Covers where fast setting times are required, such as when re-opening for traffic is going to occur within the working day.

Pack 24 Kg.
 
Part No. 1743
Compund 16A

Used in sealing of ducts. A polyisobutylene base material which comes in stick form.

1 Kg.
 
Part No. 1744
Compund 21A

A PVC Solvent used for joint Duct54D in building and exchange lead-ins.

Tin 500ml (sufficient for approximately 25 joints.)
 
Part No. 1177
Resin Pack 6A

For sealing the base of cabinets cross connection. Pack 1.7L 2.25 Kg.
 
Part No. 1184
Mixture No 2

Used in the preparation of Sleeve 30A, 31A and 32B and for filling the key holes of carriageway manhole covers. This is a plastic cement type mixture which comes in block form.
 
Twine Lacing

Used on switchboard and exchange cableforms.

Twine Lacing Medium 8oz
Twine Lacing Fine 8oz

1162
1163
 
Part No. 1518
Tape Sealing 3 (2")

Used in wrapping the joints of polyethylene and thin lead sheathed cables.

Roll 10m long x 50mm wide.
 
Part No. 1519
Tape Delf Amalgamating

For making taped joints. This tape bonds into an unlayered solid mass providing an excellent watertight seal.

Roll 10m long x 25mm wide.
 
Tape Plastic Adhesive

General purpose PVC tape.


T.P.A 12mm x 20m
T.P.A 12mm x 20m
T.P.A 12mm x 33m
T.P.A 12mm x 33m
T.P.A 25mm x 20m
T.P.A 25mm x 20m
T.P.A 25mm x 33m
T.P.A 25mm x 33m
T.P.A 25mm x 33m
T.P.A 25mm x 33m


Colour
Red

Green

Black

Cream

Black

Yellow

Cream

Grey

Yellow

Black

 

  

Code
1512

1508

1502

1506

1503

1523

1507

1511

1515

1516
 
Part No. 1521
Tape 12A

Used in the securing of polyethylene sheathed cables to Brackets and Cable Bearer.

Hank 2.5m (10 per pack)
 
Part No. 1520
Tape 11A

For tying cable core paper wrappings.

Reel 200m.

Dispenser Tape 11A.
 
Bracket Cable Bearer

Used to support cables in underground jointing chambers. Made of galvanised cast iron. The type name relates to the brackets effective length in inches.

E.L - Effective Length (mm)
O.L - Overall Length (mm)

Type
3
5
8
12
18
24

E.L
80
130
200
300
450
600

O.L
150
170
250
350
500
650
  

Code
1045
1046
1047
1048
1049
1050
 
Cable Bearer Wall Type

Used to hold bracket Cable Bearers in underground structures. Made of galvanised cast iron. The type name indicates how many Bracket Cable Bearers can be held at 3" spacing for type 2 and 6" spacing for type 3-12. Fixing holes are drilled at 3" spacing.

Type
1
2
3
5
8
10
12

Overall Length
178mm
279mm
508mm
813mm
1270mm
1574mm
1879mm

Code
1053
1054
1055
1056
1057
1058
1059
 
Part No. 1039
Pin Locking Cable Bearer

High tensile steel, galvanised pin for fixing Bracket Cable Bearer to Cable Bearer Wall Type.
 
Part No. 1062
Bracket CN

Bracket CN 14071 for holding Sleeve on Cable Bearers and in Joint Boxes 23 and 26.

Bracket CN 14071
- (Sleeve 31 A, B and C)
 
Part No. 1571
Sleeve 31A Clamp

Hinged camping collar for use with Sleeves 30B, 31B and 31C.
 
Part No. 1572
Sleeve 31C

Used for radial distribution joints up to 100 pairs in PET (including armoured) cable. This is a cap ended closure which has seven re-usable ports which are closed using heat shrink tubing.
 
Part No. 1270
Connector Wire Insulated 8A

Two wire, grease filled insulation displacement type connector for jointing insulated conductors of 0.4-0.9mm diameter for copper and 0.5-0.7mm diameter for aluminium.

Box 400 (jelly crimp)
 
Part No. 1271
Connector Wire Insulated 8B

Three wire, grease filled insulation displacement type connector for jointing insulated conductors of 0.4-0.9mm diameter for copper and 0.5-0.7mm diameter for aluminium.

Box 250 (jelly crimp)
 
Part No. 1272
Connector Wire Insulated 8C

Three wire, grease filled insulation displacement type connector for jointing insulated conductors of 0.4-0.9mm diameter for copper and 0.5-0.7mm diameter for aluminium. This is used to tee-in to existing cables without interrupting service and to this end there is a side entry on one side of the connector.

Box 250 (jelly crimp)